Problems
Troubleshooting
A failed print is no reason to think the printer is broken. Almost every problem has a few ordinary causes: a dirty or uneven bed, damp filament, a draught, unsuitable settings in the slicer. Below are the most common situations and what to check first. Change one setting at a time and write down the result, otherwise it is hard to tell what actually helped.
Before changing settings, wash the bed and check the filament: these two simple things solve a surprising number of mysteries.
How this section works: the situations are described in general terms. If the printer crackles, sparks, smells of burning or overheats, unplug it and consult the manufacturer's instructions or a service centre.
Common situations
The first layer won't stick to the bed
Most often the culprit is grease and dust on the surface or too large a gap between the nozzle and the bed. Clean the bed the way the manufacturer recommends, check that it is level and see at what height the nozzle starts printing. A draught from an open window can also pull the plastic loose.
Stringing between parts
Thin strings appear when molten plastic oozes from the nozzle during travel moves. Dry filament helps, as do the retraction settings in the slicer, which pull the material back slightly before a travel move. Change them a little at a time and print a small test piece.
Layers separate and crack
Layers bond poorly to each other if the plastic cools too quickly or is not fed in sufficient quantity. Get rid of draughts, check that the part isn't being cooled too hard, and make sure the material settings in the slicer match your filament.
The corners of the part curl up
This is warping: the plastic shrinks as it cools and pulls the edges with it. A clean bed, an even first layer, a warm spot without draughts and a wide thin brim around the part, cut off afterwards, all help a lot.
The nozzle is clogged and no plastic comes out
Clogs are often caused by dust on the filament, bits of material or a heated nozzle sitting idle for a long time. Don't poke at a hot nozzle with your fingers or random objects. How to clear it safely is described in the printer's instructions; if in doubt, ask for help.
The part comes out the wrong size
First re-check your measurements with calipers and the model's scale in the slicer. Then bear in mind that holes often come out slightly smaller when printed, and outer walls slightly larger. Print a small test section and adjust the model based on the result.
If a print fails halfway through
Stop the print
If the part has come off the bed or the nozzle is dragging a lump of plastic around, stop the print using the printer's normal command. Don't try to adjust the part by hand while the printer is moving.
Let everything cool
Wait until the nozzle and bed have cooled. Hot plastic sticks to skin and causes burns, and rushing won't speed anything up here.
Clear away the remains
Remove the failed part with a scraper, clean the bed and carefully free the nozzle of stuck plastic, following the manufacturer's instructions.
Find the cause
Look at which layer the failure began on. A detached base points to the first layer and the bed, gaps in the middle to filament feeding, and shifted layers to the mechanics or to the printer having been knocked.
Check the filament and bed
Make sure the filament hasn't tangled on the spool or absorbed moisture, and that the bed is clean and level. Often that is enough for the next print to run without problems.
Repeat and write it down
Start the print again and watch the first layers. Record in your print log what happened and what you changed. If the failure keeps recurring for no visible reason, consult the manufacturer's instructions or a service centre.
Read also
- Guides
Step-by-step advice: preparing the file, first print, calibration, removing supports, useful things for the home. The article catalogue is here too.
- Tools
Bed scraper and brush, calipers, a dry box for filament, gloves and goggles, ventilation and a print log.
- Comparisons
Filament versus resin printing, PLA, PETG and photopolymer resin, your own model versus a ready-made file from the web: strengths and weaknesses.
- Glossary
Slicer, layer, infill, supports, nozzle, first layer, post-processing and other home printing words in plain language.
- Questions
Answers about the guide, about printing and materials, about safety at home and about respecting the rights of model authors.
Sources
- Printer and material manufacturers' instructions (in general terms)
- Safety notes on working with photopolymers (in general terms)
- Editorial materials of the guide
This guide describes home printing in general terms and reflects the editors' view on the date it was prepared. Printers, filaments and resins all work differently, and menu items in model preparation software go by different names. If the instructions for your printer or material say otherwise, follow the instructions.