An independent beginner's guide to home 3D printing. It does not sell printers or materials, does not print to order and is not connected with the former site on this domain.

Guides

Practical guides

A good print starts long before the nozzle heats up. Much is decided during preparation: how to place the model on the bed, whether it needs supports, how dense to make the infill. This section brings together the tasks every beginner faces: printing a first part, tuning the printer for your filament, removing supports neatly and bringing an object to a tidy finish.

Before changing a dozen settings at once, change one and look at the result: that way you'll understand faster what affects what.

— From the editors

How to read this section: the guides are written in general terms and suit most home printers. Menu items in your slicer software may be named differently, so look for them by what they do.

Guides

Tasks that sooner or later come up for every home printer owner.

Prepare a model for printing

Lay the part on the bed on its largest flat face, check that nothing hangs in mid-air and look at the layer preview. The slicer will show where supports are needed and how long the print will take.

Glossary

Calibrate the printer

Calibration means checking that the bed is level, the nozzle sits at the right height and the filament is fed in the right amount. Start with the procedure in the manufacturer's instructions, and write down what you changed.

Tools

Choose the infill

A part is usually not solid inside but filled with a grid. Sparse infill is enough for a decorative piece, while a hook or bracket that carries a load needs denser infill and thicker walls.

Comparisons

Remove supports

Supports are removed once the part has cooled. Break them off slowly while holding the main part, and cut sharp remnants away from yourself. With resin prints, do this wearing gloves.

Safety

Finish the part

Sanding smooths out layer lines: first with coarse sandpaper, then with progressively finer grits. After that the part can be primed and painted. Sand wet or wear a mask so you don't breathe in the dust.

Glossary

Print useful things for the home

Drawer organisers, wall hooks, cable holders, handles and caps are good first projects. For things that carry weight or sit near heat, choose a suitable material and denser infill.

Questions

Catalogue of articles in English

This is where standalone Prowh articles written specifically for English-speaking readers of the guide will be collected.

What we are working on

  • How to tell from the first layer that the bed needs levelling again
  • Keeping filament dry in a damp climate or a humid room
  • Printing a drawer organiser that actually fits your drawer
  • Setting up a safe corner for a printer in a small flat or shared home

Editorial rules

  • Articles in this catalogue are written separately for each language version and are not translations.
  • Some articles link to third-party websites, including gaming services; we do not control their content, prices or terms.
  • We do not sell printers or materials, we do not print to order, and we do not publish advertising, rankings, prices or reviews.

How to print your first part: from file to finished object

  1. Find or draw a model

    Take a ready-made file whose licence allows printing for personal use, or draw a simple shape in 3D modelling software. Models are most often stored in STL format.

  2. Open the model in a slicer

    A slicer turns a 3D model into a set of layers and commands for the printer. Choose the profile for your printer and material: it already contains basic settings that make a convenient starting point.

  3. Position the part on the bed

    Rotate the model so that it has a wide flat base and as few overhanging parts as possible. The fewer supports, the easier the post-processing and the cleaner the surface.

  4. Check the layer preview

    Scroll through the layers in the preview: are any parts hanging in mid-air, are the walls thick enough, have small details gone missing? A mistake is easier to spot here than on the printer bed.

  5. Start the print and watch

    Transfer the file to the printer as described in its instructions, prepare the bed and start the print. Watch the first layers up close: they show whether the whole part will succeed.

  6. Remove and inspect the part

    Wait for the bed to cool, remove the part, take off the supports and check the dimensions. Write the settings and the result in your print log; next time it will save you time.

  • Tools

    Bed scraper and brush, calipers, a dry box for filament, gloves and goggles, ventilation and a print log.

  • Comparisons

    Filament versus resin printing, PLA, PETG and photopolymer resin, your own model versus a ready-made file from the web: strengths and weaknesses.

  • Problems

    First layer not sticking, stringing, layers separating, corners curling up, a clogged nozzle, a part that comes out the wrong size.

  • Safety

    Hot parts, fumes and dust, liquid resin, printing unattended, children and pets nearby, the rights of model authors.

  • Questions

    Answers about the guide, about printing and materials, about safety at home and about respecting the rights of model authors.

Sources

  • Printer and material manufacturers' instructions (in general terms)
  • Safety notes on working with photopolymers (in general terms)
  • Editorial materials of the guide

This guide describes home printing in general terms and reflects the editors' view on the date it was prepared. Printers, filaments and resins all work differently, and menu items in model preparation software go by different names. If the instructions for your printer or material say otherwise, follow the instructions.