An independent beginner's guide to home 3D printing. It does not sell printers or materials, does not print to order and is not connected with the former site on this domain.

layer by layer: a guide to home 3D printing

Prowh: home 3D printing, layer by layer

A home printer can do a surprising amount: print a missing hook, a little box for odds and ends, or a cap to replace a lost one. But the first encounter is often disappointing: the plastic won't stay on the bed, strings stretch between parts, and the finished piece doesn't fit. Prowh calmly explains how printing works, what happens between the model file and the finished part, and what to check yourself before deciding the printer is faulty. The advice is given in general terms, without brand or model names, so it suits most home machines.

Almost every beginner's failure comes down to three things: a clean, level bed, a careful look at the first layer, and patience while the part cools.

— From the editors

Where to start

How printing works

Some printers push out molten filament and build a part layer by layer; others harden liquid resin with light. Here is how these methods differ and what to expect from them.

Your first part

A simple model, a carefully prepared file, a clean bed and a little watching are enough for your first print to end as an object rather than a lump of plastic.

When a print fails

A layer that comes loose, stringing and curled corners are familiar to everyone who has started out. Each of these troubles has clear causes and simple ways to check them.

Safety at home

A hot nozzle, fumes during printing and liquid resin all deserve respect. Ventilate the room, wear gloves and goggles with resin, and never leave the printer unattended.

Guide sections

  • Guides

    Step-by-step advice: preparing the file, first print, calibration, removing supports, useful things for the home. The article catalogue is here too.

  • Tools

    Bed scraper and brush, calipers, a dry box for filament, gloves and goggles, ventilation and a print log.

  • Comparisons

    Filament versus resin printing, PLA, PETG and photopolymer resin, your own model versus a ready-made file from the web: strengths and weaknesses.

  • Problems

    First layer not sticking, stringing, layers separating, corners curling up, a clogged nozzle, a part that comes out the wrong size.

  • Safety

    Hot parts, fumes and dust, liquid resin, printing unattended, children and pets nearby, the rights of model authors.

  • Glossary

    Slicer, layer, infill, supports, nozzle, first layer, post-processing and other home printing words in plain language.

  • Questions

    Answers about the guide, about printing and materials, about safety at home and about respecting the rights of model authors.

Your first print in five steps

  1. Choose a simple model

    Start with a small object with a flat base and no overhanging parts: a stand, a key fob, a hook. A model like this prints without supports and quickly shows whether everything is in order.

  2. Prepare the file in a slicer

    Open the model in slicer software, choose the profile for your printer and material, and lay the part on the bed on its widest side. The slicer cuts it into layers and saves the commands for the printer.

  3. Level and clean the bed

    Check that the bed is levelled as described in your printer's instructions, and remove dust, grease from your fingers and leftovers from the last print. A clean surface holds plastic noticeably better.

  4. Watch the first layer

    Don't walk away while the printer lays down the first layer. The lines should go down evenly, lightly pressed onto the bed and without gaps. If the plastic balls up or drags behind the nozzle, stop the print and find the cause.

  5. Let the part cool

    When the print finishes, don't rush to remove it. As it cools, the plastic shrinks slightly and often comes away from the bed on its own. The nozzle and bed are still hot at this point, so don't touch them.

The essentials in brief

Do you sell printers or print to order?

No. Prowh is an independent guide. We don't sell printers, filaments or resins, we don't print things to order and we don't accept files; we only explain how home printing works.

Which printer should I buy?

We don't recommend specific brands or models. Instead, we explain what to look at: which printing method suits you, what size of objects you want to make, where the printer will stand and whether there is good ventilation there.

Can I print any model from the web?

Not any. A model file is someone else's work, and the author decides how it may be used. Read the licence before printing: some allow personal use only, some require you to credit the author, and you may sell prints only when that is explicitly allowed.

Is printing at home dangerous?

If you follow a few simple rules, home printing is no more alarming than any other household appliance that heats up. Ventilate the room, keep an eye on the printer, don't touch hot parts, and wear gloves and safety goggles when working with resin.

About the project

Prowh is an independent beginner's guide to home 3D printing. We write about everyday matters: how to prepare a model, start your first print, understand why it failed and finish the completed part. The guide has no connection with earlier websites on this domain and does not reproduce their content.

We don't name brands of printers, materials or software, we don't publish rankings and we don't sell anything. Machines and menus differ, so we explain the principle, and the exact settings are always in the instructions for your printer or material.

  • Guides

    Step-by-step advice: preparing the file, first print, calibration, removing supports, useful things for the home. The article catalogue is here too.

  • Problems

    First layer not sticking, stringing, layers separating, corners curling up, a clogged nozzle, a part that comes out the wrong size.

  • Safety

    Hot parts, fumes and dust, liquid resin, printing unattended, children and pets nearby, the rights of model authors.

  • Comparisons

    Filament versus resin printing, PLA, PETG and photopolymer resin, your own model versus a ready-made file from the web: strengths and weaknesses.

  • Glossary

    Slicer, layer, infill, supports, nozzle, first layer, post-processing and other home printing words in plain language.

Sources

  • Overview of the history of additive manufacturing (Wevolver)
  • Printer and material manufacturers' instructions (in general terms)
  • Editorial materials of the guide

This guide describes home printing in general terms and reflects the editors' view on the date it was prepared. Printers, filaments and resins all work differently, and menu items in model preparation software go by different names. If the instructions for your printer or material say otherwise, follow the instructions.